Thanks to the Hands on History Travelling Foundation, I had the wonderful opportunity to visit Gudvangen Viking market 2017. Here follows a short summary of my trip as well as some personal reflections.
Travelling to Gudvangen was done by car on a sunny summers day, the weather was absolutely amazing. This made the trip very beautiful but also made the lack of AC in the car very noticeable. The compensation for us being boiled in our own sweat was amazing scenery, a fair trade to say the least.
For you who don’t know about Gudvangen, it’s located in the western region of Norway in the municipality of Aurland in Sogn og Fjordane county.
We arrived to Gudvangen at midday but waited until evening to put up the tent in order to avoid the busiest, as well as the hottest, hours. This unfortunately gives us no pictures from the first day with its sunshine so the majority of these pictures were taken on other days when it was cloudy (all pictures except one but you’d have to figure out which one that is by yourself).
It’s a scenic place, to say the least.
The fjord water was cold and had an amazing aquamarine colour, which was difficult to capture without the equipment of a professional photographer.
On the second day we ventured out along the fjord to go swimming in the cold fjord water. Despite it being at least 20°C during the cloudiest day it was no more than 10°C in the water due to mountain water and the ocean being close at hand. Nevertheless, going for a swim was refreshing and appreciated but also fascinating because you see the mountains at all time but you tend to forget that the fjords are the opposite of mountains. That is, when you go swimming you can see how the mountain disappears down into the deep, clear fjordwater. Beautiful, cold and awe inspiring.
Gudvangen being in a fjord makes it perpetually surrounded by the green mountains. It sound reasonable enough but that doesn’t mean that it isn’t breathtaking when you see it.
Turned out that green was an exceptional nice colour that worked very well with the surroundings. The particular green as seen in the picture above was made using yellow onion skin and indigo.
Above is one of the dinners; beer, salmon, cabbage, bread and butter. Tasted amazing, 10/10 would eat again.
The Nærøyelva flows through the bigger part of Gudvangen, even though it’s difficult to see it from these picture Nærøyelva continues quite a bit in.
It’s difficult to not be impressed by Gudvangens scenic nature but not only does it look unique, it smells and sounds in a particular way as well. I remember waking up one night wondering why there was such heavy traffic in the middle of the night. Took me a while before I understood that the low murmur that my modern brain translated as traffic was in fact the sound of the many waterfalls that surrounds Gudvangen.
It was an amazing trip and one of the many thoughts that I will take with me from this trip is that environment is not purely there for the aesthetics. There is a roughness to nature which I think is a part of its beauty and partially responsible for the fascination we have for it. But the roughness also bring demands; demands about how we dress and how we work to survive in it. Or at least it did.
There is an ingenuity with mankind that is rare, an ingenuity that gives us unique tools and skills based on the region and the time we happen to live in. Based upon these tools we develop a society surrounding them, cultivating and developing them for new possibilities. In order to understand more about a culture, understanding tools are crucial. To understand tools, we must use it and evaluate its products. For this purpose, I try to put my reenactment close to what available sources there are from each century. There is a reason to such a life, a feeling and a way to value workmanship and knowledge that is hard to come by without experiencing it.
There is, of course, different ways to approach reenactment and history but this is my approach which has been reinforced by my experience in Gudvangen. I want to understand, work and learn new skills in my reenactment and I want these skills to be based of what we actual know about a certain time and place. By working to learn these skills I will see what they saw and feel what they felt; curiosity, frustration and (hopefully) success. Hopefully I’ll learn something; if not about history then maybe about myself.
This is a short instruction of how to do an indigo dye; it is recommended that you look up further literature if you plan to do an indigo dye. If you understand Swedish, Sandström and Sisefsky (1981) is greatly recommended when it comes to plant dyeing.
As a chemist, I recommend the general use of glass wares because glass as a material is inert and will generally not be permanently stained or otherwise affected by chemical reactions. This goes ESPECIALLY for handling acids and bases. For the dyeing pot it’s stainless steel or enamelled pots, I myself use stainless steel and a smaller enamelled pot when the occasion calls for it. Iron and copper pots are also usable but will affect the outcome. Avoid aluminium.
I don’t know if this is necessary but I’ll write it anyway; NEVER use any equipment once used for dyeing in cooking. Some simpler things like alum might be easy to wash away but I’m lazy and don’t like meticulous cleaning so I use completely separate sets for everything, measuring and stirring included. I also greatly recommend taking notes on what you’re doing as well as pictures. Combine these two and you will have what is commonly known as a laboratory report. In that way, you don’t have to remember everything you did, for long and how it looked. The human mind is keen on forgetting things very quickly, especially if the process was successful. Writing things down will make it easier to share information or to successfully repeat the process. This is something I myself struggle with as I often wish I would take more informative notes of what I’m doing and why.
An indigo dye needs several chemicals and materials, e.g. table salt aka sodium chloride (NaCl), ammonia (NH3), 25wt% sodium lye aka sodium hydroxide (NaOH), sodium dithionite (Na2S2O4), denatured alcohol (I use T-sprit), indigo. In order to do this as safely as possible it is recommended to read up on every chemical BEFORE dyeing as well as reading the instructions thoroughly! Use the (Material) Safety Data Sheet, something that was mentioned earlier in this post, for each substance if you’re uncertain. If you feel comfortable with all of the chemicals above, how to store them and what to do in case of a spill or other accident, then go ahead.
It would be good to quickly mention the weight percentage of the sodium hydroxide; it’s supposed to be 25wt%, which means that if you want to have a stock solution of 500 gram (approximately 0.5 L since the density of water is 1000 gram/L) then you need 75% of it to be water and 25% of it to be sodium hydroxide. This is easily done by measuring 0.75×500=375 gram of water and then add 0.25×500=125 gram of sodium hydroxide. Keep in mind that this is a exothermic process (gives off energy, in this case heat) and that sodium hydroxide is a base so take care when doing this. If you’re uncertain about what I’m talking about, please read up on some elementary chemistry; it should be covered in most high school chemistry literature. If not, my literature recommendation on basic chemistry is Chemical principles by Atkins and Jones (2013).
In indigo dyeing, there is the preparing of the vat (where the indigo is) and the dye bath (where the vat and fibres are added and the actual dyeing takes place), so look at the instructions for both of these to make sure you have enough material for each step.The indigo vat can be done indoors for several reasons, mainly because of the lack of ammonia. The use of ammonia in the dye bath makes it unsuitable to do indoors unless you have a fume hood or equally efficient ventilation (a kitchen fan is usually not up to standard). Stay outdoors for the dye bath! Plan ahead.
Material: Glass jar with a tight shutting lid that holds the total fluid volume of the vat (in this case around 190 ml)
Something to stir the indigo vat with (it will be stained if not glass or stainless steel)
Pot that can be filled with enough water to cover the glass jar
10 g indigo powder
Denatured alcohol (I use T-sprit)
165 ml 50°C water
16 ml NaOH 25wt%
10 g Na2S2O4
Put the indigo in the glass jar and add a small amount (10-15 ml) of denatured alcohol, enough so that you can stir the indigo.
Add 165 ml of 50°C water, stir.
Gently add the Na2S2O4 and stir.
Screw the lid tight shut and immerse the glass jar holding the vat in a 50°C water bath for 1 hour. Put a cork coaster or something similar under the jar to avoid it being in direct contact with the heating source and as such avoid having an uneven temperature in the vat.
Done. The vat will be green-brown in colour.
And there you go. Now you have a vat! You don’t need to use all of the vat at the same time, you can save some for another time. Just make sure to save it in a tightly shut glass jar with a minimum of air in it. Write the amount of indigo and the date on the vat so you know what’s in it and how old it is.
In order to have different shades of blue you can always use more or less indigo, 10 gram would give a somewhat lighter blue.
A pot/cauldron that can take 16 L of water PLUS additional fabric and/or yarn without being crammed
A stick or something to stir with that is long enough so that you can comfortably stir the pot at the bottom without dipping your hand in the bath
Thick, long protective gloves
About 1000-2000 gram of fibre depending on the wanted colour depth and intensity
(Graduated measure cylinder (mätglas) is not necessary but really good to measure ammonia and sodium hydroxide in)
Dye bath: 16 L water
70 ml ammonia
30 g sodium dithionite
200 g table salt
200 ml vat
Heat the water to 50°C, make sure you have attained a stable temperature as the temperature greatly affects the outcome (deviation at most +/- 5°C).
Add the ammonia (avoid the vapours as much as possible). From now on only use protective gloves when handling anything containing liquid from the bath.
Add the sodium dithionite. After this you should avoid adding air/oxygen in the bath. Stir gently.
Add table salt and wait until the salt is dissolved in the dye bath. If not properly dissolved, the salt will gather at the bottom of the pot and leave dark stains on the fibre that comes in contact with it. To stir the bath in order to more quickly dissolve the salt is fine, just do it carefully in order to avoid stirring down unnecessary amounts of oxygen.
Gently add vat. The surface of the dye bath should have an oily look to it.
Prepare an appropriate amount of fibre (100-500 g) by immersing it in lukewarm water (about 30-40°C) for about 5-10 minutes before dyeing so that it won’t float to the surface when it’s dipped in the dye bath and to avoid dry spots.
Remove the wet fibres from the lukewarm water and remove excess water from fibres by gently squeezing it.
Carefully add the fibres to the dye bath. Avoid creating air pockets in the fibre that will add unnecessary oxygen to the bath or limiting the fibre access by having tangled fibres. Untangle everything and make sure that every part of the fibre is in contact with the dye bath and kept under the surface of the dye bath throughout the dyeing process.
Wait 5-10 minutes. The fibres will look yellow in the bath.
Remove the fibres slowly from bath, avoid dripping as oxidised droplets will add oxygen to your dye bath. The yellow-greenish look on the fibres will slowly turn blue when in contact with oxygen.
Let the fibre oxidise for about 20 minutes to see to what extent the fibre has been dyed.
If wanted, repeat step 8-11 up to a totalt of 4 times for deeper hues and shades.
Use appropriate tools when removing the fibres from the bath. Always wear protective gloves. Protective glasses can also be used if deemed necessary.
Rinse fibres thoroughly after dyeing. Sandberg and Sisefsky (1981) recommends an acidic after wash using acetic acid to increase the general rubbing fastness of the dye.
When dyeing loosely woven wool, it is possible that there will be a shrinkage because of the temperature of the bath. To avoid this, test the shrinkage of your fabric beforehand and add shrinkage allowance accordingly.
Some additional notes on indigo dyeing:
Don’t be in a rush. Take your time, read and think things through. Prepare it in several steps, do the calculations one day and then dye another day. It usually takes me half a day to do one batch of indigo dye and I usually do the calculations the day before.
Not happy with the first result? Then just redo it, an intense indigo dye can save the blotchiest of fabrics.
Make sure you always have some extra fibres for swatches so that you can check that the dye bath gives the colour you wanted. Just remember to wait 20 minutes so the swatches are properly oxidised and thus representative of the end result.
If you get a stain of indigo powder somewhere, just clean it up using a paper tissue with denatured alcohol. But if you get a stain of indigo vat somewhere then there is no helping you. Sorry. To avoid this, be careful and keep a clean working area and remove everything that you could not handle being stained. Wear working clothes, you will get stains on your clothes.
Concerning historical sources of indigo for the 10th century, it is the same dyestuff in both woad and indigo; indigotin. According to my understanding, it is at the moment not possible to distinguish the indigotin source in older fabrics and findings even though it is probable that the main source of indigotin in the Nordic countries during the 10th century is woad. As an example, the indigotin found in the Mammen grave is said to be either woad or indigo (Hägg, Inga et al., 1991). On a different note, madder is also found at Mammen even though there are no evidence of the cultivation of madder in Scandinavia at that time. The dyestuff, procedure and result is the same for both woad and indigo; the main difference right now is that indigo powder is a lot cheaper than woad powder which unfortunately makes a lot of difference for me. But then again, the rest of my reenactment gear is not on the level that the breaking point of its authenticity would be the origin of the dyestuff. But when it is, I’ll do something about it.
Currently, I think that the trickiest part with indigo dyeing is knowing when to stop. At some point, you will not have enough indigo and/or too much oxygen in the bath and that will make the dyeing uneven or without effect. But exactly where that point comes is something I’m currently trying to figure out. Experience is key.
Keep in mind that the above, numbers and all, is more what you’d call “guidelines” than actual rules.
Happy dyeing y’all.
Atkins, P.W., Jones, L. & Laverman, L. 2013, Chemical principles: the quest for insight, 6th, International edn, W.H. Freeman and Company, New York.
Last week I had the opportunity to do a quick visit to Stockholm and as such I naturally did what anyone would do, I spent the evening at The Swedish History Museum (Historiska Museet). Because, luckily enough, the museum had extended opening hours on a weekday that coincided (promise!) with my visit in Stockholm. As such, I spent the evening hours walking around in their exhibitions. It was a good time, I especially liked the iron age ceramics as well as the viking exhibition. I appreciated the opportunity to see source material in real life and especially some of these well debated findings; yes, I am thinking of the silver top that was presumably a part of a hat. There was a guided tour happening just at that display when I passed it so I didn’t have a good opportunity to photograph it, you can check it out here though.
When visiting museums I often think that “I don’t need to take pictures because there is a better picture of this somewhere else” but I have realised that I appreciate the pictures afterwards even though they might be shaky and out of focus. My photos are certainly not top quality but they kind of makes all the difference in the end on what I remember and what not. I’ll share some of the pictures I liked here because, as anyone with a pinterest account has discovered by now, there are a very finite number of pictures of available source material online so it’s nice to see something from a different angle for once. Remember though that they are taken through a glass window of the display with my cell phone and under less than perfect circumstances.
In order to support the museum and to get some decent pictures of the findings, I bought three booklets about their exhibitions and a bag with valkyries on it. Support your local museums!
I also happened to see some findings that I have replicas which is always fun! The findings were displayed in the museum but the since it was kind of troublesome to take pictures due to the lightning and display cases, I compare the replicas with pictures of the findings from the booklets instead. I really appreciate the effort people go through in creating replicas, especially when they look this good.
Note the differences in source material and replicas; I dare say we sure are fond of symmetry nowadays. I try to keep this in mind when working with reenactment, to not be bothered by asymmetry and ease up in our strive for perfection. Somehow, it’s more difficult than I would care to admit, especially when it comes to your own work.
There turned out to be a lot of viking items in this post but I enjoy the pre-christian designs and expressions. Not trying to be rude but I think there is a limited number of times that you can depict iconic bible moments and still keep it interesting. The amount of bible depictions in the source material for the medieval times and the 14th century clearly surpasses that number. On the other hand, this gives us some context so I guess it might be a good thing. Ah well.
Unfortunately enough, the textile department of the museum was closed at the time of my visit so I’ll have to revisit again at another time. But if nothing else, check out their database that I used to find information of all the above material; I’ll definitely keep this in mind in the future, extremely handy!
All in all, go visit The Swedish History Museum (Historiska Museet) in Stockholm if you have the opportunity to do so! They have a lot of nice things.
I’ll try to dig up som old corpses, dyes and crafts that I have done over the years to start with. First out is my very first plant dyed yarn! It was 200 gram of a thick, bone white, single ply wool yarn from Marks & Kattens.
I like thick yarns to naalbind socks and mittens, because it’s quick work and becomes soft, though I have heard that socks made from thicker single plied yarn supposedly gets worn out more easily. I have a pair of socks in this yarn and this has yet not happened to me but maybe I just have baby soft feet incapable of causing harm (not true) or feet sweaty enough to full the wool instead. For example, I can show you how socks made from this yarn has turned into a nice felted sole (if you’re into that kind of thing). But then again, these are just event socks; which means I only use them 1-2 weeks a year so the non existent wear and tear of these socks is not representative of everyday use.
Findings of a single plied sock is yet to be found, I somehow have an idea of it mostly being 2-ply, 3-ply and 4-ply yarn but right now I can’t seem to find anything about this except this small picture on the sock from of the Coppergate findings. If anyone can help me out with a better source on this I would welcome it.
Back to the dye! Done in December 2014, it is the most unregulated and unknown dye I’ve done since it was made from leftovers from a tansy bath that I got from my excellent partner in reenactment crime, Anna (check out her blog!). As such, I have no idea of weight ratio or actually anything about what this was. It could be a mixture of plants for all I know. However, the dye was made with about 2 L of left over bath so I just diluted it with enough water so that the wool could move around and get a even spread of dye in bath. The pot in the picture is a 15 L pot so I’d say that I might have used a ratio of 1:4 of left over dye bath to water; I don’t know why I used such a small amount of water, I should’ve used more but who knows, maybe I was having a bad day…
In the case of dyeing, if your pot is 50L or less, I’d recommend to use as much water as possible. Even though it’s diluted it’s still the same amount of dye just less concentrated (if anyone remembers m [gram] / M [gram/mol] = n [mol] where n is the mole that represents the amount of substance, in this case the amount of dyestuff. Using the formula for concentration c [mol/m3]· V [m3] = n [mol] we can see that n is unchanged since an increase in volume would affect the concentration as well and as such leave the mole unchanged). A larger volume of water is beneficial for the diffusion of the dye bath so that the dye can spread itself evenly through the bath and uneven colouring can be avoided (Dumitrescu et al., 2008; Lewis and Rippon, 2013; Mehrparvar et al., 2016). If possible, I will make a separate blog post where I briefly elaborate further on relevant thermodynamics, diffusion and heat transport.
Anyhow, don’t let confusion get to you just because I used some different words, standardised units and chemical formulas; all of you probably can intuitively come to terms with the idea that more water is needed to give a good flow throughout the yarn and it’s not bad to apply some basic science or analysis in your everyday life. Who knows, it might come in handy later on (the real struggle here is for me to avoid being overly vague or incorrect because if I at some point am, the internet hellhounds will haunt me for the rest of my natural life). Sandström and Sisefsky’s (1975) recommendation on this is a 5 L bath per 100 gram wool which I’d say can be considered a guideline as good as any.
The pre-mordant used was alum, KAl(SO₄)₂·12H₂O but is also known by the name of aluminium potassium sulfate dodecahydrate, used with the generally recommended ratio of 20wt% mordant (Conradi-Engqvist, 1978; Kierstead, 1950; Sandberg and Sisefsky, 1970). Deviations from this recommendation is Vrande (1982) and Råbergh (1978) with 15wt% alum but instead they commonly uses additionally 10wt% tartar or uses post-mordants with a 5wt% of copper sulfate, CuSO4, or iron sulfate, FeSO4, respectively.
It is sometimes considered that older recipes and ratio for pre-, post-, and meta-mordants are overdoing it concerning the recommended amount of mordant; I have not yet done any further testing of different mordant ratios since I only have two pots for dyeing at the moment and as such, I currently consider myself lacking enough equipment to do any good mordant ratio variations. Nevertheless, I think I’d like to give it a go at some point. But yes, I’d be inclined to agree that less mordant can be used but it will affect both the colour and the fastness against water as well as light. Less mordant means less colour intensity and also less wash fastness and less resistance to light. That is, using an insufficient amount of mordant will cause most of the dyestuff to eventually be washed out. Using mordant attaches dyestuff to the fabric due to the complex coordination properties of metals (Lee and Kim, 2004; Uddin, 2014; Mehrparvar et al., 2016), e.g. you can get different hues as well as increased levels of fastness against water and light using mordant (Waheed and Alam, 2004; Burkinshaw and Kumar, 2009; Dumitrescu et al., 2008).So, again, it all depends on what you want. If you want a dyed material with a well defined colour that should be relatively unaffected by both sunlight and washing, it would be suitable to use mordants. Nevertheless, it is also good to use resources sparingly and using too much mordant of any kind is a waste, the question is; how much is too much? What’s the smallest amount that can be used and still get an effect?
Anyhow, enough mordant talk for now, I will have to get back to that subject later.
I don’t have any notes from this dyeing but I think the pre-mordant was done for 60 min at ~90°C and then leave the wool in the mordant bath until cooled. Then I let it hang for a day or two to dry before it was time for the tansy bath. Same procedure with the tansy bath, 60 min at~90°C, let the wool cool in the dye bath.
Despite not having any exact knowledge of what I was doing it turned out Very Nice.
Considering the colour intensity of the yarn, I could’ve probably used the bath for several more dyes but for I had no further dyes planned so I didn’t. The plot twist of this story is that the yarn was supposed to be for my friend in Stockholm but the package was lost or stolen from the letterbox during the christmas holidays. I mourned for a couple of months but I still have a small piece left that I took for reference.
Anyhow, this is so far the most tragic tale I have in the art of plant dyeing so stay tuned for happy excitement as we prod at the dyes of the past.
Conradi-Engqvist, Cecilia (1978). Spinna, växtfärga och forma av tråd: från naturfiber till textil. Spinna ull och lin och forma av tråd : med färg- och kompositionsövningar : studieplan. Stockholm: LT
Kierstead, S.P. 1950, Natural dyes, , United States.
Lee, Y. & Kim, H. (2004), Dyeing properties and colour fastness of cotton and silk fabrics dyed with Cassia tora L. extract, KOREAN FIBER SOCIETY, SEOUL.
Lewis, D.M., Rippon, J.A. & Ebook Central (e-book collection) 2013, The coloration of wool and other keratin fibres: edited by David M. Lewis, Department of Colour Science, University of Leeds, UK and John A. Rippon, CSIRO Materials Science and Engineering, Australia, Wiley, Chichester, West Sussex.
Mehrparvar, L., Safapour, S., Sadeghi-Kiakhani, M. & Gharanjig, K. 2016, “A cleaner and eco-benign process for wool dyeing with madder, Rubia tinctorum L., root natural dye”, International Journal of Environmental Science and Technology, vol. 13, no. 11, pp. 2569-2578.
Råbergh, Hilkka (1978). Färga garn och tyg: växtfärgning, syntetfärgning på bomull-batik, syntetfärgning på ull. Västerås: Ica bokförl.
I was going to wait a while before doing this kind of post but I was struck with sudden inspiration when I stumbled upon a Facebook group that focuses on plant and mushroom dyes. What is plant dyeing? Or, as it sometimes is referred to, natural dyeing?
Wikipedia is generally considered as an unreliable source but it somehow reflects society and the general public, and as such they say the following: “Natural dyes are dyes or colorants derived from plants, invertebrates, or minerals. The majority of natural dyes are vegetable dyes from plant sources—roots, berries, bark, leaves, and wood—and other biological sources such as fungi and lichens.”
The alternative to plant dyes is synthetic dyes which are dyestuff that is not naturally occurring. The first synthetic dye was Mauveine in that was synthesised in 1856 and subsequently launched on the market in 1857. Even though picric acid was prepared as a dye as early as 1771, the foundation of the synthetic dye industry is generally attributed to the Mauveine synthesis and commercialisation (Christie, 2001). Before that point, all dyes were derived from natural sources.
But today plant dyeing seems to have a unique meaning only known to the user themselves. The general consensus is that fibres are being dyed but the means of doing it varies. For some, it means using plants for dyeing; for others, it means only using natural sources they can harvest out in the nature by themselves to dye with; and for a few it means to dye only using things with trivial names (incorrectly but commonly referred to as a “chemical free” process). I will try to avoid going into semantics about what is and is not a chemical by posting a link to this blog post about “What is – And What Isn’t A Chemical?“. As much as I’d like to tell you everything, I don’t have the time (and besides, who says you’re going to believe me?). But if you DO believe me, let me sum things up by saying that every material is a chemical, even if it exists in your home and has a trivial name.
To use a plant dye example; the chemical Ca(OH)2 is commonly referred to as slaked lime, which is constantly presented as an alternative to the chemical ammonia, NH3, in indigo vats. Unfortunately, they are both chemicals so if your aim is to do a dye without chemicals you have failed to understand the fundamentals of dyeing (and chemicals). Although, there are other reasons to use Ca(OH)2 instead of NH3 and vice versa but replacing one with another in the hope of becoming chemical free is futile work. Even that handmade natural oak-spirit-soap you bought at the last Carpe Diem-fair is made out of chemicals; even though the individual who sold it to you guaranteed it was not. There is no way around it. Minerals are also naturally occurring (Richardson, 1997), which makes copper sulfate, Cu(SO)4, legit as a plant dyeing material if we go by the the definition of plant dyeing (plants, minerals, invertebrates; derived from nature; naturally occurring etc.). And as such, we have the conspiracy unfolded right here, similar to when Frank Thorn realises the plot twist of the movie Soylent Green;
Nature is chemicals! They’re making chemicals out of nature. Next thing they’ll be synthesising organic molecules themselves. You’ve gotta tell them. Chemicals are naturally occurring!
But really though, I don’t think this comes as surprise for anyone (neither did the soylent green revelation!). I mean, where else would chemicals come from, the highly unnatural space? And, now that we think about it, are we sure that space isn’t natural as well? Anyhow, I do feel the need to mention that there exists a general idea of what is and what is not chemicals even in the field of chemistry; because we are also, believe it or not, a part of society and its norms. It is considered childish and unnecessary to refer to everything as chemicals all the time because it’s a basic fact which tells us nothing new. But on the other hand, in communication you have to specify what you’re talking about and herein lies the difference; you can’t just say chemicals if you want other people to understand you! You should explain what chemical you’re referring to, which isn’t that much of a stretch really since you probably have one in mind already.
I don’t believe you! If everything is chemicals then how do I know what is toxic and what is not?
In case you didn’t know, table salt can be toxic to humans. Apple seeds contains cyanide and cyanide is also toxic to humans (Holzbecher et al., 1984). All in all, there is stuff like this everywhere and about everything can be toxic, it’s only a matter of concentration and dosage. The thing is, you don’t digest or wash your eyes with washing powder, hairspray, rubber, deodorant, hair dye, thinner, oil, nail polish or shampoo because you know that it might not be good for you. You seldom use these things outside of its intended purpose because you also know that it might become weird. And don’t get me started on people who smoke and drink but are afraid of chemicals eventually being hazardous… Nevertheless you don’t hesitate to use it in your everyday life. But for some, reason, this kind of thinking completely disappears as soon as the word chemical is involved. Which is weird, because it’s basically the same things going on there. There ARE information and literature on how to plant dye and what to use and how. Follow those instructions and you’d be fine. Another source of information is to check out the (Material) Safety Data Sheet (M(SDS)) for a certain chemical. Here is a MSDS for table salt.
A short, but very unsatisfying, summary would be to implore you to use your common sense and you’ll be fine. If you still want more I’d recommend to study toxicology.
But there is too much information, I can never remember any of this!
You don’t have to, most people use books to write down the most important things and there is always the internet to enlighten us.
Why did you have to make everything difficult, my way of thinking and evaluation is much easier!
I didn’t make anything (except this pesky blog), nature did.
But I am sure that people used only onion skins before the first synthetic dye, none of these mordants and acids! Those are all 20th century ideas!
I am not so sure. Unfortunately, as we often do in historical reenactment, we lack a lot of sources. Though one source that we do have is from a handwritten manuscript from around 1860; that is only a few years after the first synthetic dye was created and the processes described in manuscript involves no synthetic dyes. In fact, all these recipes described would soon be abandoned for the much more efficient and less costly synthetic dyes (Sisefsky and Sandberg, 1979). The manuscript has one example for dyeing blue wool yarn and it involves potassium cyanide (KCN), hydrochloric acid (HCl), disulfuric acid (H2S2O7), potassium aluminium sulfate (alum, KAl(SO4)2) and potassium bitartrate (cream of tartar, KC4H5O6). How’s that for a cocktail? Kind of put our modern concern about using a 20wt% alum mordant at a shame. Of course this doesn’t mean that this is what was used in the earlier centuries but we can at least say that these chemicals are not exclusive to the 20th century and their use in plant dyeing processes precedes the 19th century development of the synthetic dye industry .
I dye only using onion skin! I am chemical free.
Pelargonidin is what is in the dyestuff of onion skin (Uddin, 2014). If you’re not using a mordant, it would be sufficient to just say that you’re dyeing without using a mordant.
Surely I use less hazardous material than in the industry? My environmental impact has to be less than if I’d buy the industrially dyed material?
The current industry has had several iterations, process optimisations and experience which generally makes the industry a lot more efficient than a single individual with little to no technical equipment and experience. Most developed countries also have a lot of regulations that is to be followed regarding the process and its emissions, no one will measure your own amount of trace metals in your plant dyes (Griffiths, 1984). As I previously mentioned, synthetic dyes are far more efficient than plant dyeing which means you’d generally consume less resources using synthetic dyes compared to plant dyes (Sisefsky and Sandberg, 1979). The difference here is to how to view the emissions; if you compare emissions and resource consumption per kilogram of dyed material, the industrial dye would probably be using less resources. A common theme is that there is a lot of transport involved in production, which is not good thing for the environment but also makes calculations more difficult. Even so, there are ways that these are accounted for (an example would be the Life Cycle Assessment) but you will always have to limit the analyse. I’ll try to explain this with an example; if you’d dye yarn that was made at the farm next door you’d be responsible for less emissions than if you’d buy imported yarn. But then again, if the sheep that made the wool at the farm next door lacks food in the pasture and needs to support feed and then that food needs to be transported there, should that transport be included in the emissions for the yarn? And where was that food grown and using what fertiliser? As you probably understand, this thinking can derail pretty quickly but I hope you see the problem with deciding a number for any of these emissions and impacts which is also why you should be critical to anyone producing such numbers, what is included and what is not? Often the numbers are in favour of whoever is presenting them so my advice is to be critical.
A summary of this would be to say that it’s impossible to know but an individuals plant dyeing process is probably more inefficient than the industry and has an unknown quantity of residuary chemicals in it (unless you analyse every batch, which would be cool but very expensive but at least you’d know what you’ve got). The industry can, of course, also have an unwanted quantity of residuary chemical but this is why we invest in quality and try to only buy fabrics and clothes from countries with regulations and decent working conditions, right?
My dyes DO become resistant to both light and water if I do it using only the dyestuff like blueberries/lupins/beetrot and no mordants!
No, they don’t. What happens is that you get a dyed material that WILL be drained of colour when exposed to water or sunlight (Burkinshaw and Kumar, 2009; Dumitrescu et al., 2008; Waheed and Alam, 2004). If you keep the dyed material away from water and sunlight things then you’d be fine but you’d also be living in a very dry and dark place. If you aim to be eco friendly, natural, climate considerate, environmental friendly or whatever buzzwords you use in justification then consider both the time, energy and work that you put into this. If you’re using any kind of heating in the dyeing process you are literally wasting energy and time; not to mention if you use wood as a fuel for heating the bath which has a LOT of exhaust gases that are harmful and currently not very popular (Bari et al., 2010;van Lith et al., 2006; Tissari et al.,2007).
I only use plant dyes in a cold bath and using sunlight so I am the most environmental friendly dyer there is and I am always pleased with my dyes and colour hues!
Good for you, get back to me when you can dye 2 kilograms of heavy wool evenly with a deep colour intensity while also getting water and light fastness in a cold water bath at pH7 using only dyestuff. Snark aside, if you HAVE achieved something like what I just said in a reproducible and controlled manner, please do share it with the world (that shit would be Nobel prize worthy)! That would be an amazing feat and of great benefit to the whole planet.
The question to ask in these cases is, if all kind of processing and chemicals are to be avoided at all costs then why dye it in the first place? The most natural way to avoid any kind of dye process is to NOT dye. Personally, I think that the natural colour and hues of wool is superior to many other hues, this is why a large part of my reenactment kit is non dyed wool. If you completely want to avoid any kind of chemistry happening then plant dyeing, or any kind of dyeing, is not for you. And before you even think it, there is nothing like good or bad chemistry; nature doesn’t work that way. Endless energy consumption is something to be avoided as well as pollution. Water is a resource and electricity doesn’t spawn spontaneously at the energy company, globally it is often a result of combustion (often coal) and somewhere there is a exhaust coming from that energy production. Is it worth the time and energy if the result will fade within a month?
On the other hand, there are several other things you can do if you want a more sustainable lifestyle. Some examples would be to eat less meat, promote local farms and production, don’t throw away food, travel less (unless by foot, bike or sailing), recycle, repair, invest in quality and so on. And my primary advice is to consume less. Simply put, buy less shit. Remember, it’s not a bargain if you don’t need it.
In the end, however, everyone does as they please but be aware of what you’re doing and the reasons for doing it. It is totally ok to plant dye for your own sake, and peace of mind; I encourage that since that is what a hobby is about! But don’t do it for the wrong reason or try to claim the moral high grounds by saying that it’s more natural (what even is natural? Infant deaths, scurvy, polio, venomous snakes, anaphylactic chocks, cyanide, dental cavities, space?) or without chemicals (IT’S NEVER WITHOUT CHEMICALS!). Instead, to specify what you’re avoiding and for what reason would be a better way of communication if you want to show some sort of situational awareness and at the same time be understood by other people.
Griffiths, J. 1984, Developments in the chemistry and technology of organic dyes, Blackwell Scientific, Oxford.
Holzbecher, M. D., Moss, M. A. & Ellenberger, H. A. (1984), ‘The cyanide content of laetrile preparations, apricot, peach and apple seeds’, Journal of Toxicology: Clinical Toxicology 22 (4), 341–347. PMID: 6098693.
van Lith, S. C., Alonso-Ramírez, V., Jensen, P. A., Frandsen, F. J. & Glarborg, P. (2006), ‘Release to the gas phase of inorganic elements during wood combustion. part 1: development and evaluation of quantification methods’, Energy & Fuels 20 (3), 964–978.
Sisefsky, Jan & Sandberg, Gösta (1979). Receptsamling från Schwartzska färgeriet i Borås efter handskrivet original från 1860-talet på Borås museum. Borås: Borås museum
Richardson, H. W. (1997), Handbook of copper compounds and applications, CRC Press Tissari, J., Hytönen, K., Lyyränen, J. & Jokiniemi, J. (2007), ‘A novel field measurement method for determining fine particle and gas emissions from residential wood combustion’, Atmospheric Environment 41 (37), 8330 – 8344.
Uddin, M.G. 2014, “Effects of Different Mordants on Silk Fabric Dyed with Onion Outer Skin Extracts”, Journal of Textiles, vol. 2014, pp. 1-8.
Waheed, S., & Alam, A. (2004), Studies of some natural dyes, JOURNAL-CHEMICAL SOCIETY OF PAKISTAN, 26, 255-263.
After much consideration and many thoughts about it I have decided to start blogging about my dealing with reenactment and crafts in general. Reasons? Everyone is doing it and I have a lot of pictures that are pretty nice and as such, I’ve decided to share some of them here along with some thoughts.
I’ll try to introduce this blog, the purpose and myself in this entry.
This is a blog that will cover my thoughts, ideas and pictures of my dealings with reenactment and crafting. I started doing reenactment and crafting more seriously in 2010, I have dabbled in somewhat vaguely related activities in my youth but it was first in 2010 that I started to spend serious time and money on it. I say reenactment and crafting because my part of reenactment mainly consists of crafting. I know that fighting is a big thing in reenactment but I have simultaneously to this interest trained muay thai for several years and has as such never felt the need to participate in the fighting part of reenactment. As such, my focus is mainly everyday life of civilians.
The periods that I am currently involved in is 10th century and 14th century in the Nordic countries. This is a choice based on my location in the west of Sweden, available events (because to be honest without deadlines, nothing would be done) and my limitation as a seamstress. As fancy as the later centuries are, I am not a tailor and will only shame the century and stress myself out by trying to achieve an acceptable level of quality.
In my crafting, I am aiming towards a simpler style. I am trying my best to stay true to the available source material in both eras; which doesn’t give much space concerning the 10th century in since most of the findings from the Nordic countries consists of a few threads and a lot of heavy gold and silver bling. Considering that gold is still pretty expensive you still have to be filthy stinking rich to wear everything true to many graves. Filthy stinking rich is something that I’ll never be so I’ll just try to stay humble and dirty instead.
Considering sources I do the best I can, as many other, by looking at available findings and books. This is loosely regarded to as research in this hobby, which kind of waters down the expression to be honest (as I have met very few who actually does professional scientific research). But then again, this is just a hobby and it’s just a matter of semantics in this case. What I do is that I try to look up available findings, discuss it and work out a decent framework that works for me based on what seems plausible and possible for me to do without going insane. It sounds deceptively simple.
Over the years I evolved a soft spot for plant dyeing so hopefully I can shine some light on this subject here. It is an activity that is in general somewhat vaguely described, with loose terms and its own trivial names; maybe so because it doesn’t have to be very precise to work well and therefore the precious skill of accuracy is sadly neglected in this case. I am a fan of choice and I promote accuracy so that eventual inaccuracy that takes place is a conscious choice . But considering that this is a hobby and takes place in our spare time, sometimes there is not time nor energy left for accuracy; which is also okay. For me, the point of crafting is not primarily accuracy but to learn something and to create something. Although I confess like to make progress in the things I do and in order to progress I need to evaluate my actions and in order to evaluate my actions I need accuracy. And here we are. In summary, I try to be accurate but I don’t beat myself up if I’m not.
(Un)fortunate enough, I am at the moment a full time student at a major technical university in Sweden and as such I have precious little time to do anything else than work and trying to have a working everyday life. My bachelor is in chemical engineering, my master is in nanotechnology and materials chemistry and I am currently writing my master thesis work at the department of chemical engineering / organic chemistry. As such, I am a scholar of science and I am not afraid to use it! But to be frank, most of science boils down to understanding that there are things that you don’t understand. Not much of a comfort, I know, but it actually helps and makes the world less unpredictable in some aspects. But then again, expecting the unexpected is a paradox in itself and quite tricky to do in real life but now I’m getting off topic. Anyhow, I’ll do what I can and I’ll make no promises.
Concerning the particular design and features of this blog in general, I’ll try to work out some decent theme here so if everything looks weird I’m probably trying something new and failing. Don’t give up on me though, I need the page clean and working as much for my own sanity as well as yours.
Also, as you might have guessed I am not a native speaker of English but I’ll try to keep this blog in english to the best of my abilities; because, it would seem that there are more people not speaking swedish doing this weird business.
If you’re reading this today (the 24th of February 2017) you are a very eager internet person and all of this information is up to date. If you’re reading this when accidentally scrolling to the bottom of my blog, then I don’t know where you’re from in time but you are a very persistent cookie and I’ll keep you in mind.